Medium Viscosity / Medium Temperature Down-Hole Silicone Fluids
Clearco Down-Hole Silicone Fluids possess the thermal/pressure/viscosity and density properties that are critical in the ever harsher environments in the Down-Hole oil and gas exploration industries. They are widely used for the most extreme environments where high temps and high pressures are present.
With declining reserves and advances in technology, the oil and gas industry is drilling ever deeper. In these environments, fluids are required that can remain stable at the elevated temps > 200°C as well as the higher pressures.
The fluids in this section are divided by viscosity as well as by temperature.
Down-Hole Silicone Fluids can be used to dampen vibration and serve as a heat transfer / heat stable fluids in a wide range of Down-Hole pressure gauges, geo-steering instrumentation, transducers, cables, temperature and process recorders, control valves, calibration equipment, flow meters, thermostats.
Down-Hole Silicone Fluids are characterized by their their wide service temperature range, high resistance to oxidation, high damping action, excellent lubricity, compatibility with virtually all o-rings, little viscosity change at extreme temperatures, and high dielectric strength.
Down-Hole Silicone Fluids can be used in the most extreme environments where high rates of vibration, pulsation and pressure are encountered Unlike conventional petroleum based fluids like mineral oil, silicone fluids exhibit extremely high compressibility and will not coagulate. Even at pressures of 4,000 MPa, the fluids will not solidify. A properly selected silicone fluid can significantly extend the service life of equipment and provide more accurate reading in doing so.
DPDM-400 and PM-125 High Temperature Down-Hole Silicone Fluids provide even higher thermal stability and wider service temperature ranges than the PSF-Down-Hole Silicone Fluids
View product specs:Click here to view
Availability: 1 gallon (3.6kg), 5-gallon pail (18kg) & 55-gallon drum (200kg)
Service Temperature: -40C to 230°C (closed system / absence of air)
|Viscosity||Specific Gravity||Pour Point||Flash Point||Viscosity/Temp Coefficient||Thermal Expansion (cc/cc/c 0-150C)||Thermal Conductivity g/cal/cm/sec °C|
Use: Medium Viscosity Down-Hole Silicone Fluids possess the thermal/pressure/viscosity and density properties that are critical in the ever harsher environments in the Down-Hole oil and gas exploration industries. These Fluids are linear Polydimethylsiloxane fluids (CAS# 63148-62-9) that range in viscosity from 50cSt to 1,000cSt (centistokes) @ 25°C.
Medium Viscosity Down-Hole Silicone Fluids are characterized by their low pour points, high damping action, newtonian behavior under shear, low viscosity change at temperature (VTC), excellent lubricity, high dielectric strength, wide service temperature range and inertness to virtually all components such as transducers, instruments, gauges and cables.
Medium Viscosity / Medium Temperature Down-Hole Silicone Fluids are effective for use in instruments and gauges that will operate in more extreme environments where higher temperatures and higher pressures are present. They have a service temperature range of -40°C to 230°C (close to air) and can withstand High Pressures
By nature, Silicone fluids are hydrophobic and prevent humidity from entering the gauge/instrument housing. This is very important. At low temperatures, water condensation can freeze and cause damage to the sensitive parts within the gauge/instrument housing. Ultimately, Silicone Damping Fluids will extend the service life of the equipment that it fills and provide more accurate readings even in the harshest of conditions.
Unlike conventional petroleum based fluids like mineral oil, Down-Hole Silicone Fluids exhibits extremely high compressibility and will not coagulate under pressure. The lower the viscosity, the higher the compressibility will be. Silicone Down-Hole Fluids will not solidify even at high pressures of 4,000 MPa
- Dampen vibration in gauges, instruments, meters and sensors
- Protects internal components against vibration, freezing and corrosion.
- Extends service life of gauges, instruments, meters and cables.
- Wide service temperature range
- High Flash Point
- Remain Stable under Extreme Pressure
- Low viscosity change at temperature (low V.T.C.)
- High Dielectric Strength
- Environmentally friendly: VOC Exempt & HAP Free
- Hydrophobic- will not absorb water
*not recommended for silicone rubber due to possibility of swelling